News, Jobs and Higher Education
free sex justene jaro.
hd porn bonded teen machine pounded doggy style.
http://www.smellslikeafish.com

How to Transition a Removable Implant-Supported Solution to a Fixed Prosthesis (Part 2) – Spear Education

25

Author’s Note: This is Part 2 in my series on preexisting implants in full-arch reconstructions. The introduction article, “How to Use Preexisting Implants in Redesigning a Full-Arch Reconstruction,” was published first, and you can also read Part 1 in Digest.

Nowadays it is quite common to receive patients who have preexisting dental implants. This is no longer a novelty, and it will only become more common in the years to come.

The challenge in these situations is being able to navigate quickly and to provide the patient with acceptable solutions when they are dissatisfied with their preexisting ones. It’s important to become an active listener to patients’ concerns, desires and ultimately their treatment expectations.

In Part 1 of this series, I described how to efficiently transition a removable implant-supported solution to a fixed prosthesis (in two appointments) with digital technology.

Generally, it is recommended to wait 4-6 months to validate the esthetic, functional and structural performance of the prototype provisional restoration, as well as the motivation and hygiene of the patient before embarking on the fabrication of a definitive prosthesis at higher cost.

In this case, the patient presented one year after insertion of the prototype prosthesis, ready to continue with treatment.

After a thorough evaluation the following distinctive aspects were evident:

As we were getting ready to proceed, it was important to consider the different potential design options for the patient:

Financially, a titanium bar with denture teeth would be the least costly of all three options, but the challenge with this design was the esthetic management of the obliteration of the screw access hole in the midfacial aspect of the three anterior teeth with composite resin and its eventual maintenance.

Once it was thoroughly explained to the patient, along with the inherent advantages that a ceramic restoration poses over utilizing denture teeth on a titanium bar, it was decided to make a CAD/CAM monolithic Zr framework with four cemented crowns on top of the four maxillary incisors.

Conceptually, we could manufacture the definitive prosthesis with a minimum number of additional steps, essentially, scan the prototype, make the design of the zirconium framework, using the previous information and fabricate CAD/CAM restorations with relative ease.

The only additional step here was to make an open tray analog impression of the implants, to fabricate a master cast.

Once the models, implant abutments and prototype had been digitized (Figures 1-3), as previously mentioned, the accesses to the implant screws in the anterior implants were located on the buccal area (Figure 4). It was decided to make individual crowns on the four incisors to cover the access holes to the screws and solve the esthetic problem.

With the zirconium framework, the four anterior crowns were designed (Figure 5) and milled, leaving minimal space for facial layering and, at the same time, gingival ceramic in the Zr framework (Figures 6-8).

Once the final prosthesis was finished, the titanium inserts were carefully cemented following adhesive cementation protocol using resin cement (Figure 9).

During the insertion appointment, it is necessary to validate the following elements (Figure 10):

Once the passive seating of the prosthesis has been validated and the occlusion has been verified, as well as adequate access to hygiene, the screw-tightening protocol will be carried out, which consists of the following steps:

As the following figures show, this restorative design successfully provided all the esthetic and functional goals sought out by the patient and our practice team — an esthetically pleasing fixed solution that provides adequate lip support in a sagittal view, a transitional line that is perfectly concealed underneath the lip, adequate hygiene access, and a structurally robust material that withstands the force of mastication (Figures 11-14).

The case presented illustrates an expedited process of converting an implant-supported removable design into a fixed design utilizing digital technology to design and manufacture not only the prototype provisional restoration but the definitive ceramic solution as well.

Ricardo Mitrani, D.D.S., M.S.D., is a member of Spear Resident Faculty.

This content was originally published here.

Comments are closed.

juli asthon threesome fucked in the ass.sesso gratis phub hot messy creampie for april blue by creampei. big booty ms damn.girls xxx oily booty slut drilled.